Search results
-
Pulling RR Brk Drums??
Ya dude no shitting u I think my drum wasn't seated right I've never has that happen before Sent from my Galaxy Nexus using Tapatalk 2- gberland
- Post #11
- Forum: Suspension
-
Pulling RR Brk Drums??
Yuppers 100 ft. Had to have been something with my drum glad nothing major happened Sent from my Galaxy Nexus using Tapatalk 2- gberland
- Post #9
- Forum: Suspension
-
Pulling RR Brk Drums??
Ummm no picture s. I don't do allot of rear brake drum brakes but all I no is somehow the lugs worked themselves off and my wheel came off no threads where stripped no real damage actually and the wheel drum was loose as hell and I was able to slip it off with just my hand after the tire fell...- gberland
- Post #7
- Forum: Suspension
-
Drive belt removal
Ya sorry for being a dick dude that's what kids make a person at times Lol well I'm not sure if the picture posted. Correctly ??? Couple posts back but I literally just YouTubed it dude an the video pops right up. Luckly there is a flat spot sticking out on the side of the tensioner enough so u... -
Drive belt removal
Dude I ain't the first person to do it this way there is a video on YouTube showing how to do it this way LOL an like I say I needed my car for Friday for Fort McMurray I wasn't gonna wait around a week to order a special tool , an i sure didnt feel like pulling the engine mount so I did what... -
Drive belt removal
Lol. It works but u just have to be careful. , I only did it this way because I didint have access to the proper tool an I need my car road worthy by Friday because I will be traveling with it. For work, mabey just save yourself the trouble an order the tool before hand Sent from my Galaxy... -
Drive belt removal
Hmmmm harbour freight hey? I think that's the one I needed its pretty low profile hey? The snap on. One didn't fit. However. The back yard way worked fine lol Sent from my Galaxy Nexus using Tapatalk 2 -
Drive belt removal
Well that's who I pull wrenches for FORD an I see tons of engineering flaws lol Sent from my Galaxy Nexus using Tapatalk 2 -
high pressure overflow - Evap system
Most likely an EVAP canister issue sounds like u have some kind of restriction because usually the vapors from the gas tank vent through your EVAP canister vent valve if there is some kind or restriction in between there an your vapors are not properly venting they will vent through your gas cap...- gberland
- Post #2
- Forum: LS, LT, LTZ
-
Drive belt removal
I borrowed my co workers SNAP ON one an i didn't work there is absolutely no clearance to fit one in there although there may be a special GM tool that fits without doing this. Anyways. I'm glad this way worked otherwise I would a been screwed good ol YouTube is a lifesaver some times lol Sent... -
Drive belt removal
Not sure I'd anyone has had trouble reaching the tensioner release hole to remove an install your drive belt ,its almost impossible without loosening engine mounts but I found a video on YouTube about it using a jack an a block of wood works pretty good Lol just be careful how high u go with... -
seat belt bolt
Its 50 I'm sure. Take the torex socket an insert it long as its nice an snug an does not move around in the bolt groove then your good an don't forget to use HEAT!! micro torch Sent from my Galaxy Nexus using Tapatalk 2 -
Pulling RR Brk Drums??
This may be a dead thread but thought I'd throw it out there ,when re adjusting your rear brake drum make sure to tighten the star wheel until the point were its snug an you cannot pull off your drum by hand. Basically you wanna be tighter then looser here. , from personal experience Lol my...- gberland
- Post #5
- Forum: Suspension
-
no start/ no crank
its the alternator guys checked battery state of charge was at 12.2volts should be at least 12.4-12.5 threw a booster pack on an she started right up, held a digital volt meter on battery terminals while engine was running and voltage was at 12.0 volts and not charging should be around...- gberland
- Post #2
- Forum: Engine/ Performance
-
seat belt bolt
Yes. Torex 50 I believe. An your going to have to get a mini torch an heat the bolt for a good 4 minutes to melt the lock tite then after that immediately start cranking on it. Make sure u got a good ratchet an not a cheap one. Use. Mac. , snap on. , Craftsman, Matco etc. Sent from my... -
no start/ no crank
greeeaat !! just in time for the cold its close to winter my Balt has been sitting for about ten days now used it once when i got home went to start it tonight and no crank all the accessory lights come on headlights etc. but no crank any known or common issues with these balts mines a 06...- gberland
- Thread
- Replies: 1
- Forum: Engine/ Performance
-
stripped seatbelt bolt recommendations?
they say u got a 50 percent chance when wearing a seat belt of surviving the crash guess its better than 1 percent- gberland
- Post #16
- Forum: LS, LT, LTZ
-
New Mechanic
yup fist of all you'd want to check your front end suspension, ball joint, wheel bearings, condition of your tires , rims, if u find somthing loose this will need to be replaced there is not alot to the suspension on a cobalt which is a basic mcpherson strut , just one ball joint, wheel...- gberland
- Post #6
- Forum: LS, LT, LTZ
-
Custom floor
ya so mabey this summer that will be my next Mod unless i sell it -
-
Custom floor
I was thinking entire floor ?? i may just look into getting alluminum floor inserts mabey even if i have to make em -
Custom floor
does anyone kno any sites were they sell like custom floor inserts i guess kinda like floor mats?/ i wanna rip out all my rug im sick of steam cleaning it ???? -
'05 starts creaking in steering column when turning
pretty much what this guy said sums it up , i kno one time in summer mine was doing that too so i sprayed the rubber grommet under neath the hood the one that the steering colum goes through and it stopped, as per dealership if u dont like the chevy dealership u can always try a small shop???- gberland
- Post #4
- Forum: General Discussion
-
DSC01533 HID headlights and Black OEM style housings
- gberland
- Media item
- Comments: 0
- Album: Farewell album Sept 2012 / the last power wax
