Go Back   Chevy Cobalt Forum - Cobalt SS | Cruze | Saturn ION | Pontiac G5 Forum > Chevy Cobalt Forum - Cobalt Models > How To's > Other How to Stuff

Sponsored Ads
Register to remove these ads.

Other How to Stuff

How To perform a TPMS relearn (w/ & w/o keyless entry)


This is a discussion on How To perform a TPMS relearn (w/ & w/o keyless entry) within the Other How to Stuff forums, part of the How To's category!
Figured I'd toss this up for the people that either don't have an owners manual or don't know where to ...




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 11-19-2011, 01:27 AM   #1 (permalink)
 
YelloEye's Avatar
Official F250 Tow Vehicle
Platinum Member
Super Mod
 
Join Date: Jul 2009
Location: Renton, WA
Age: 28
Posts: 6,299
Send a message via AIM to YelloEye
Default How To perform a TPMS relearn (w/ & w/o keyless entry)
Figured I'd toss this up for the people that either don't have an owners manual or don't know where to find the Ebook (hint: chevrolet.com)

For the RKE guys just follow all the steps and ignore the blue lines. Non RKE people substitute the blue line for the line above it in your steps.

TPMS Matching Process for Vehicles with Remote Keyless Entry (RKE)
TPMS Matching Process for Vehicles without Remote Keyless Entry (RKE )

1. Set the parking brake.

2. Turn the ignition switch to ON/RUN with the engine off.

3. Press and hold the Remote Keyless Entry (RKE) transmitter’s lock and unlock buttons, at the same time, for about five seconds to start the TPMS learn mode. The horn sounds twice indicating the TPMS receiver is ready and in learn mode.
3. Using the Driver Information Center (DIC), press the INFO and Set/Reset buttons at the same time for about one second. Then press and release the INFO button until the TIRE LEARN? message displays. Press and hold the Set/Reset DIC button for approximately three seconds to start the TPMS learn mode. The horn sounds twice to indicate the TPMS receiver is ready and the TIRE LEARN ON message displays.

4. Start with the driver side front tire. The driver side front turn signal also comes on to indicate that corner’s sensor is ready to be learned.

5. Remove the valve cap from the tire’s valve stem. Activate the TPMS sensor by increasing or decreasing the tire’s air pressure for about eight seconds. The horn chirp, can take up to 30 seconds to sound. It chirps one time and then all the turn signals flash one time to confirm the sensor identification code has been matched to the tire/wheel position.

6. The passenger side front turn signal comes on to indicate that corner sensor is ready to be learned. Proceed to the passenger side front tire and repeat the procedure in Step 5.

7. The passenger side rear turn signal comes on to indicate that corner sensor is ready to be learned. Proceed to the passenger side rear tire and
repeat the procedure in Step 5.

8. The driver side rear turn signal comes on to indicate that corner sensor is ready to be learned. Proceed to the driver side rear tire, and repeat
the procedure in Step 5.

9. After hearing the single horn chirp for the driver side rear tire, two additional horn chirps sound to indicate the tire learning process is done. Turn the ignition switch to LOCK/OFF. If no tires are learned after entering the TPMS learn mode, or if communication with the receiver stops, or if the time limit has expired, turn the ignition switch to LOCK/OFF and start over beginning with Step 2.
9. After hearing the single horn chirp for the driver side rear tire, two additional horn chirps sound to indicate the tire learning process is done. The LEARN COMPLETE message displays if all four tire positions are learned. Turn the ignition switch to LOCK/OFF. If no tires are learned after entering the TPMS learn mode, or if communication with the receiver stops, or if the time limit has expired, the TIRE LEARN? message displays on the DIC. Turn the ignition switch to LOCK/OFF and start over beginning with Step 2.

10. Set all four tires to the recommended air pressure level as indicated on the Tire and Loading Information label.

11. Put the valve caps back on the valve stems.


__________________

Last edited by YelloEye; 11-19-2011 at 01:36 AM.
YelloEye is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 8 (0 members and 8 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Keyless/Remote Entry cobaltime "How To" Request 4 02-26-2012 11:11 PM
Keyless Entry CongdonJL "How To" Request 8 10-25-2010 09:57 PM
keyless entry markcline LS, LT, LTZ 0 08-15-2010 05:23 AM
car alarm/keyless entry ??? Jn2 Audio & Electronics 10 03-02-2010 10:47 PM
Keyless remote entry and radio not working caitlin Audio & Electronics 11 01-24-2010 10:00 AM





1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93